Free Super Saver Shipping Eligible Learn More

Lumenier LUX Flight Controller

4.3 3
SKU: GF-4243
You will earn 40 points for buying this product

Availability: Out of Stock

As low as $3.70/mo with Affirm Learn More

Write a review earn 100 points




The Lumenier LUX flight controller provides high quality flight control using the powerful F3 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX Flight Controller. Achieve gyro refresh rates up to 8kHz (high speed SPI) using popular Betaflight and Raceflight firmware along with ultra low looptimes. The LUX is Cleanflight compatible using the RACE target. Batch 1 will ship with Cleanflight.

The Lumenier LUX is a very low profile board allowing it to be mounted in a variety of ways. The board also comes with a set of pin headers you can optionaly solder on. Alternatively, signal wires can be soldered directly to the pads to save on size and weight. The LUX supports PPM or Serial RX (including Futaba, FrSky, S.BUS). A signal inverter is already included for S.BUS. Please note: Baseflight firmware is not supported, and PWM input for individual channels is not supported. 

Hardware Features

  • USB Conflict resolution - Hardware inversion, SBUS or telemetry can be used on any of the 3 available hardware serial ports. USB will not interfere with peripherals.
  • High Speed SPI 8kHz Gyro
  • MPU interrupt connected to F3, allowing the F3 to know immediately when fresh data is available.
  • Dedicated Boot button for easy firmware flashing.
  • Reinforced solder pads for trouble-free direct soldering.
  • Extremely low profile design.
  • Recessed, sideways pin headers. Also enables soldering of all wires directly to pads without use of any pin headers.
  • Integrated FRSky RSSI Filter (RC filter).
  • Input voltage 6v to 24v. Power the board directly from flight pack up to 6S (on 'BAT' pad only!).
  • VIN + VBAT merged - A single wire to power the board will provide voltage input and Telemetry/OSD voltage data.
  • Filtered voltage output - output 5v 1A (and 3.3v where applicable) to power peripherals such as GPS, RX, BLACKBOX, OSD. 5v/3.3v RX selectable.

Software/Hardware Features

  • Cleanflight support (RACE target).
  • BLHeli flashing supported (BLHeli bootloader pass-through).
  • Raceflight ready
  • Betaflight ready


  • STM32F303RCT6(256kB flash) 32-bit processor
  • MPU6500 Gyro/Accelerometer
  • High quality, gold plated PCB
  • Highest quality components, individually sourced to meet Lumenier standards
  • Micro USB connector for programming
  • Dimensions: 36x36x6mm (includes USB in height)
  • Mounting Holes: 30.5mm square to center of holes 
  • Weight: 6g


  • 1x Lumenier Lux Flight Controller
  • 2x 2x7 Straight Pin Headers



Additional Information

SKU 4243
Manufacturer Lumenier

You may also be interested in the following product(s)

Black Polyamide Standoff Set (6mm)

Black Polyamide Standoff Set (6mm)

Regular Price: $3.99

Special Price $2.99

SP Racing F3 Flight Controller (Deluxe)

SP Racing F3 Flight Controller (Deluxe)

Lumenier QAV210 CHARPU Carbon Fiber FPV Quadcopter

Lumenier QAV210 CHARPU Carbon Fiber FPV Quadcopter

Acro Naze32 Flight Controller rev6 (w/ pin headers)

Acro Naze32 Flight Controller rev6 (w/ pin headers)



Additional Info

Now on sales N/A