SizeStandard Tubing insertion depth15 mm Mounting positionAny DesignBlanking plug Pack size10 Structural designPush-pull principle Operating pressure for entire temperature range-0.095 MPa ... 0.6 MPa Operating pressure for entire temperature range-0.95 bar ... 6 bar Operating pressure for entire temperature range-13.775 psi ... 87 psi...

SizeMini Nominal width2.2 mm Tubing insertion depth11.5 mm Type of seal on screwed plugSealing ring Mounting positionAny DesignStraight design Pack size10 Structural designPush-pull principle Operating pressure for entire temperature range-0.095 MPa ... 0.6 MPa Operating pressure for entire temperature range-0.95 bar ... 6 bar...

• KingTech G4 utilizes SBus data transmission. • Engine/ECU integration, all operating parameters including total run time are all recorded into the engine. • The smaller and lighter external Data Relay Module (DRM) is responsible for all data, signal and power transmission. • Pump:...

K-180G5 SPECIFICATIONS Diameter: 103mm / 4.05” Length: 251mm / 9.88” Weight: 1540g / 3.39lb Maximum RPM: up to 130000 Thrust: 18kg @ 15°C / 40 lb @ 59°F EGT: 700°C max Pump type: Digital sbus brushless pump KP600DP Battery:11.1v Lipo ( At least 2200mah 35C )...

2M x 600mm roll of genuine Oracover 21-091 Silver covering used on Boomerang RC Jets

2M x 600mm roll of genuine Oracover 21-071 Black covering used on Boomerang RC Jets

2M x 600mm roll of genuine Oracover 21-052 Dark Blue covering used on Boomerang RC Jets

2M x 600mm roll of genuine Oracover 21-023 Ferrari Red covering used on Boomerang RC Jets

2M x 600mm roll of genuine Oracover 21-010 White covering used on Boomerang RC Jets

Includes: - RDT Unit x 1pc Used for: - Jet Central SE turbines    

Includes: - RDT Unit x 1pc Used for: - Xicoy V10 (Merlin, Kingtech G1, Jetcentral pre-SE, ATJ and more)    

Heavy duty Jet fuel fitting clunk with .1875 (3/16) I.D. hole. Measures 2.25" x .5" dia. Weighs 1.5 oz.

Protect your Turbinator 2 wings with PennBags!  Double protection with a heavy duty quilted outside, with soft flannel on the inside! PENNBAGS ARE MADE IN THE USA!    

Replace canopy for Elan V2 Black Colorcategory-jets,category-jets-brand-boomerang-rc-jets,category-jets-brand-boomerang-rc-jets-model-elan-v2,category-jets-brand-boomerang-rc-jets-model-elan-v2-model-elan-v2

Includes: Landing gear AXIS x 1 set Use for: K175 Drake/M169 Havok

UAT mount for the composite Boomerang RC 120cc UAT's. Securely mount the Boomerang UAT in your RC Gas Turbine Aircraft with confidence. Mount clamps over the UAT with 2.5mm screws and nuts (provided). Set of 2.

Filter mount for the Kingtech RC gas turbine fuel filters. The filter is held in the mount with the provided zip ties. Mount includes two small sheet metal screws for mounting into the fuselage.  

Fuel Line Holder. Expertly designed for convenience and efficiency, Our 3D printed Fuel Line Holder is perfect for fuel line routing. Say goodbye to tangled lines and your turbine installations. Available in 4mm and 6mm sizes Sized to fit 4mm and 6mm Festo Tubing...

Our servo connector mount is designed to accept male servo housings. The female mount has a built-in safety clip to prevent the connector from becoming unattached.  Set includes two mounts with screws, two female servo connector housings, two male connectors with pins to fit...