MAXX ASG FLYBARLESS SYSTEM WITH RESCUE FUNCTION

PERFORMANCE-INNOVATION-AFFORDABILITY

Manual: https://bit.ly/3k4vp4T

Introductions:

With the aim to build the best flybarless system at affordable price, MAXX flybarless unit is

designed with most advanced MCU gyro and 6-axis sensors to deliver best performance and full

features at the price everyone can afford. Designed by a team of pilots with years of experience

and tested by best pilots in the world, this MAXX flybarless system not only brings affordable

flybarless units but also the most innovative product to the market.

Very low sensor offset drift due to temperature and long flight time. That will give a really

well-balanced for tail and cyclic.

Cyclic and throttle Servo 760us type supported.

SRXL2 and Telemetry supported.

Can be upgraded to an “Automatic Glow plug system” for nitro helicopters by equipping

additional MXK-1004 device.

Vibration Resistant :

MAXX Flybarless System uses newest technology sensors with very high sample rate, high

resolution and low thermal offset drift. The flybarless unit is extremely vibration resistant and

very stable flight for any helicopter size.

The MEMS sensor inside the Maxx FBL can read 4 to 16 times faster with extremely low noise.

So it is capable of analyzing and eliminating high frequency vibrations.

Also for that reason, the sensor inside the Maxx FBL is capable of upgrading to a GPS autopilot,

it is capable of detecting the smallest moving in the air.

Not only that, it makes your servo always controlled with the least noise signal.

Fast respone from sensor:

It reacts quickly and corrects the smallest movement of your heli to provides smooth and stable

control. So the tail and cyclic direction is very good under all flight conditions, more power tail

hold.

Simplified Setup:

Easy setup with MAXX Software. Customers can use mLink port for connection to MAXX

programs card and MAXX ecosystem in the future.

MAXX flybarless system brings a feeling of good flying with the default setup, reducing the first

setup time. Especially the new tail control algorithm offers good tail control with default setup on

all helicopter kits.

Ability to tunning tail gain by the transmitter (CH5).

Advance Setup:

Ability to customize Cyclic, Tail PID gain according to more flight styles and mechanical

difference of each helicopter. You can separately setup the gain of elevartor and aileron.

Bank manage: The Maxx has 3 Cyclic, Rpm banks memory allows you to set 3 flight modes

accordingly.

Dual Satellite Port and SRXL/SRXL2 support with telemetry:

The MAXX flybarless has Dual Satellite Port providing more reliability for large helicopters and

long range flights, ability to BIND by MAXX software or program card.

Built-in Electric and Nitro Governor:

MAXX active governor can throtle compensation , it calculated according to cyclic, collective,

tail, RPM and other status of Flybarless units. It offers very stability in RPM and more powerful,

more efficiency with no effect to the tail.

The RPM is set exactly the RPM value for each Bank.

Nitro Governor: MAXX flybarless supports Governor for Nitro Helicoper, using magnetic RPM

sensor connect to RPM in pin of unit. Minimum 7 chanels on transmitter is required for Nitro

Governor. The throtle chanel is set up to V-shape for fast respone. RPM is decided by CH7

(AUX2) channels on TX to trigger the Bank, setting and not decided by throttle chanel.

The Maxx supports 760us throttle servo.

Electric Governor: Use RPM wire output of Esc or RPM sensor connect to RPM input pin .

Minimum 6 chanel transmitter is required for electric governor. You can use 760us for throttle

servo.

Event Logging and High sample rate Vibration logging:

The memory of unit stores data of 5 last flights.

Event logging: Time of Radio signal, motor run/stop , BEC voltage drop

Vibration logging : Ability to review the vibration level when flying by graph form on the MAXX

software

AutoTrim Piro:

No more manual adjust for swashplate. With MAXX flybarless, there is no need to spend a lot of

time to balance the swashplate. The software can detect unbalance of swashplate in piro hover

flight and autotrim the swashplate. It can function correctly even in high winds.

Rescue:

Rescue mode is activated when the helicopter tilt angle is over threshold degrees with ground

and have event Gyro gain (CH5) value drops from high to below centre value (1520us). The

helicoper will automatically flip back then automatically increase the height. Within 3 seconds the

rescue mode will exit.

With advance accelerator sensors our MAXX flybarless system has the most accurate calculation

for most accurate rescue. This saves a lot of crashes and a great tool for beginners to learn to

fly.

Example: CH5 on Tx is 35% for flight, so you should be set CH5 on Tx is -35% (or 35% normal

mode, not AVCS) for rescue mode , reaction of the tail will not change.

Drop Radio Signal Indicator:

The LED light on the MAXX unit will blink if detecting more than 50ms radio signal loss. This can

be viewed in table Logger in the MAXX software.

Bec Drop Detector:

Nowadays, servos are very strong and getting stronger, many crashes are due to weak BEC or

bad connection. With MAXX flybarless, there is no more worries about this. Introducing an

innovative feature: BEC Drop Dectector that helps prevent many crashes. MAXX flybarless

keeps reading voltage of BEC continuously before and during flight, if BEC is weak and voltage

drops over 0.5V, the red LED on MAXX flybarless unit will double flashed to inform pilot the

problem. The problems are also logged and viewed in table logger in MAXX software for

reference.

LowBec safety setting: It is only checking at startup. If the BEC is below the voltage threshold

have been set the heli can’t fly, the initialize process is not completed.

Ability to GPS upgrade: Upgradable to 10 axis Fight Controller with GPS flight mode. The unit

is compatible with Maxx GPS addon board (MXK-1003) to add barometer, compass turn Maxx

FBL into auto-hover, Return to Home for sacle heli and soft 3D trainning.

Dimensions:	36mm x 28.5mm x 15mm (LxWxH) / 18g
Application:	Any helicopter size, Nitro and Electric Compatible
Receiver Support:	S-Bus Ready, PPM , DSM2/DSMX Satellite,SRXL/SRXL2/SPM4649T Serial Receiver, JR X-Bus, MaxxBus and Ex-Bus receiver
Cyclic Servo Support:	Digital 1520us and 760us(only setting by program card)
Tail Servo Support:	760uS / 1520uS – Up To 560Hz Frequency
Input Power	3.6 – 9V

Manual: https://bit.ly/3k4vp4T